Make a donation

Author Topic: Spreader needed for Lowering  (Read 1475 times)

Offline liver

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 14
  • -Receive: 15
  • Posts: 980
Spreader needed for Lowering
« on: January 18, 2010, 01:04:45 pm »
where could i purchase one of these??

how much are they?

are they really essential for changing springs??

cheers

Liver

Offline MAT ED30

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 82
  • Posts: 5728
  • Vwr fan boy
    • Email

Mods yes but way too many to stick in this little box

Offline liver

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 14
  • -Receive: 15
  • Posts: 980
Re: Spreader needed for Lowering
« Reply #2 on: January 18, 2010, 03:54:03 pm »
its not the spring clamps im after but cheers for looking anyway mate

its the spreader tool so i can get the strut off

Offline markymark

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 21
  • -Receive: 55
  • Posts: 2369
Re: Spreader needed for Lowering
« Reply #3 on: January 18, 2010, 03:56:21 pm »
Dont you need the spline tool to get the strut off? I had to buy a set of spline sockets from Halfords, think they were about £20 ish!

Offline liver

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 14
  • -Receive: 15
  • Posts: 980
Re: Spreader needed for Lowering
« Reply #4 on: January 18, 2010, 04:17:26 pm »

im not sure tbh all i see in the lowering threads is a tool call the spreader tool

im confused haha cars gettin lowered on sunday and the tool is needed

Offline liver

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 14
  • -Receive: 15
  • Posts: 980
Re: Spreader needed for Lowering
« Reply #5 on: January 18, 2010, 04:41:15 pm »
heres the thread that goes on about the spreader tool

http://www.mk5golfgti.co.uk/forum/index.php?topic=7974.0

Offline mortygttdi

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 44
  • -Receive: 146
  • Posts: 2370
Re: Spreader needed for Lowering
« Reply #6 on: January 18, 2010, 04:41:38 pm »
Just use a bolster chisel something with a thick tapered end will do it. Dont go spending your money on something your only gonna use once.  

Darren

Offline QD MBE

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 15
  • -Receive: 102
  • Posts: 2497
Re: Spreader needed for Lowering
« Reply #7 on: January 18, 2010, 06:56:29 pm »
Make one. 

Measure the gap in the strut, and get an allen key close to that size.  I think it is approx 6mm.  Then file/grind a flat on one of the points of the key, and then all you need to do is insert the key and turn it until the slot opens and sits on the flat and the opposite point.


Hope that makes sense.
 :smiley: