Make a donation
« previous next »
Pages: [1]   Go Down

Author Topic: how to cut the engine cover to accomodate my induction pipe  (Read 4328 times)

Offline gtisteve

  • Taking part
  • ***
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 26
    • Email
how to cut the engine cover to accomodate my induction pipe
« on: May 27, 2010, 09:27:09 pm »
hi everyone,  I have seen a few bits and bobs on this but as i am handing this over to a mate of mine to do for me he asked if there was a detailed walk through of where to cut.


and someone also said that maybe the scirocco cover would fit and still allow for induction pipe

thanks in advance everyone
Logged

Offline vRStu

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 90
  • -Receive: 159
  • Posts: 2562
    • Octavia-vRS Information Resource
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #1 on: May 28, 2010, 07:19:11 am »
I don't think the TSi cover does fit.

Logged
Stu...

Quartz Grey Audi A4 3.0 TDi S-Line Quattro, 7 Speed S-Tronic, 19" Twin Spoke Alloys, Alcantara Upholstery with Silver Stitching and Heating, Sat Nav High, B & O Sound, Audi Music Interface, DAB Radio, Parking Advanced with Rear View Camera, Advanced Keyless Entry, LED Interior Light Pack, Hill Hold Assist, Heated and Electrically Folding Mirrors, Through Load.

RNS510 Video in Motion unlocking, PIN recovery & DVD Region Free available

Offline RedRobin

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 380
  • -Receive: 442
  • Posts: 16627
  • BIALI Motorsport's Chief Horn Blower
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #2 on: May 28, 2010, 09:18:51 am »
Logged


On facebook: https://www.facebook.com/robin.procter.50

Throbbin' Red Mk5 GTI DSG with too many mods to list - Have Fun but Safe Journeys!

Offline gtisteve

  • Taking part
  • ***
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 26
    • Email
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #3 on: May 28, 2010, 11:15:47 am »
thanks robin i had seen that one but was looking for a proper step by step were to cut etc what bits are needed etc
Logged

Offline RedRobin

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 380
  • -Receive: 442
  • Posts: 16627
  • BIALI Motorsport's Chief Horn Blower
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #4 on: May 28, 2010, 01:15:05 pm »
^^^^
I've seen one somewhere but don't think it was on this site. Probably a link from here though. Have you tried a Search?
Logged


On facebook: https://www.facebook.com/robin.procter.50

Throbbin' Red Mk5 GTI DSG with too many mods to list - Have Fun but Safe Journeys!

Offline illektronik

  • Always Involved
  • ****
  • Thank You
  • -Given: 10
  • -Receive: 5
  • Posts: 78
    • Email
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #5 on: May 29, 2010, 12:58:17 am »
Hi Steve. It's pretty intuitive. Just separate the cover into it's 2 parts, and start trimming it back based on pics you've seen off modified covers. I just followed the lines of the actual engine cover.

I cut mine back base on photos alone. For the top, cut it something like this, and then just make the lower section match. It will all make sense if you cut the top first.


Logged

Offline gtisteve

  • Taking part
  • ***
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 26
    • Email
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #6 on: June 06, 2010, 09:38:37 pm »
thanks man,

    gonna give this a bash when my mate gets time, i just dont have the tools
Logged

Offline flyboy1976

  • Always Involved
  • ****
  • Thank You
  • -Given: 25
  • -Receive: 15
  • Posts: 493
Re: how to cut the engine cover to accomodate my induction pipe
« Reply #7 on: June 13, 2010, 10:14:08 am »
ive just done mine, first attempt at it went perfect!!! takes a fair bit of time :signLOL:
Logged
Pages: [1]   Go Up
« previous next »