Make a donation
« previous next »
Pages: [1]   Go Down

Author Topic: Wheel spacers query?!  (Read 1385 times)

Offline Toast

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 12
  • -Receive: 3
  • Posts: 779
  • Oot n By all the Keyboard Warriors
Wheel spacers query?!
« on: July 27, 2010, 10:47:09 pm »
Hi

Bought a set of H+R 10mm ultra light wheel spacers off Owen lcr on here picked them up from Rubbertoe 2 night :happy2:  Headed home 2 fit them onto the rear axle only 2 find that the spacer will not butt tight against the hub of the car due to a machined recessed edge inside the spacer?!  :confused:s

My question is as Owen had these on the front of his car are the front and back spacers different?!

Cheers

Toast
Logged
Editon 30, no-0472-, 1/4mile 13.6sec@Crail-Giac 348bhp,345lbsft,Milltek tbe,s3 Cooler,Helix single mass clutch kit,Eibach Coilovers,Bsh Cold Air Intake , Autotech HPFP,s3 brakes,Speedline Turini's,Xenons

Offline Greeners

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 201
  • -Receive: 199
  • Posts: 8812
    • Email
Re: Wheel spacers query?!
« Reply #1 on: July 27, 2010, 10:49:48 pm »
Not as far as I'm aware as I had 4 x fitted to my ED30 and they did not have markings to suggest front-rear?

I will say that they are designed not to fit 100% flush until the wheel is on and the bolts are tightened.  :happy2:
Logged

Offline Beddie

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 76
  • Posts: 1303
    • Email
Re: Wheel spacers query?!
« Reply #2 on: July 27, 2010, 10:54:56 pm »
H&R do have different types for front and rear fitment iirc..
For the 10mm hubcentric ones i have its part number 2055571B for front fitment and the A ones for the rear i've been told?
HTH

Logged


Tornado Red ED30 : Number 1644 - Gone

Carbon Grey Edition 35 - Here

Offline Toast

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 12
  • -Receive: 3
  • Posts: 779
  • Oot n By all the Keyboard Warriors
Re: Wheel spacers query?!
« Reply #3 on: July 27, 2010, 10:57:23 pm »
Aha thanks beddie :happy2: al take a note of that number and check in the morning sounds about right just my luck :fighting:
Logged
Editon 30, no-0472-, 1/4mile 13.6sec@Crail-Giac 348bhp,345lbsft,Milltek tbe,s3 Cooler,Helix single mass clutch kit,Eibach Coilovers,Bsh Cold Air Intake , Autotech HPFP,s3 brakes,Speedline Turini's,Xenons

Offline Beddie

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 76
  • Posts: 1303
    • Email
Re: Wheel spacers query?!
« Reply #4 on: July 27, 2010, 11:02:40 pm »
Quote from: Toast on July 27, 2010, 10:57:23 pm
Aha thanks beddie :happy2: al take a note of that number and check in the morning sounds about right just my luck :fighting:
No probs mate  :happy2:
Heres a post from the scirocco forum that explains it in a bit more detail..

http://www.sciroccocentral.co.uk/forum/viewtopic.php?f=34&t=4444
Logged


Tornado Red ED30 : Number 1644 - Gone

Carbon Grey Edition 35 - Here

Offline Toast

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 12
  • -Receive: 3
  • Posts: 779
  • Oot n By all the Keyboard Warriors
Re: Wheel spacers query?!
« Reply #5 on: July 27, 2010, 11:07:27 pm »
Cheers buddy :happy2:
Logged
Editon 30, no-0472-, 1/4mile 13.6sec@Crail-Giac 348bhp,345lbsft,Milltek tbe,s3 Cooler,Helix single mass clutch kit,Eibach Coilovers,Bsh Cold Air Intake , Autotech HPFP,s3 brakes,Speedline Turini's,Xenons
Pages: [1]   Go Up
« previous next »