Make a donation
« previous next »
Pages: [1]   Go Down

Author Topic: Fitting Cat Back Milltek - Advice  (Read 3495 times)

Offline bodger00

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 23
  • -Receive: 20
  • Posts: 521
  • A wish called Zonda
Fitting Cat Back Milltek - Advice
« on: March 09, 2011, 08:27:54 pm »
I have bought a cat back off someone on here (non res). I am really pleased with it . I can't wait to fit it but I need to know if I am missing any bits to get it to fit to my OEM system?

Are there any clips/reducers missing that I am going to need? If so do you know where I can get them from?

Logged

Offline big al

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 27
  • -Receive: 93
  • Posts: 2607
    • Email
Re: Fitting Cat Back Milltek - Advice
« Reply #1 on: March 09, 2011, 08:33:24 pm »
Looks to me like it should fit ok without any problems, garage will probably stick a D shaped clamp on to hold them all in place.
Enjoy the noise!  :wink:
Logged

Offline bodger00

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 23
  • -Receive: 20
  • Posts: 521
  • A wish called Zonda
Re: Fitting Cat Back Milltek - Advice
« Reply #2 on: March 09, 2011, 08:44:52 pm »
Cheers Al :happy2: Garage is me so I guess I can use the clamp that's already on the car.
Roll on the weekend :party:
Logged

Offline parks

  • Always Involved
  • ****
  • Thank You
  • -Given: 3
  • -Receive: 17
  • Posts: 370
  • Red ED30 No. 1778 Detailing World member
Re: Fitting Cat Back Milltek - Advice
« Reply #3 on: March 09, 2011, 10:28:32 pm »
Do you have to cut the old one off?
Logged
Standard: Rear parking sensors, Parrot Bluetooth
Retro fitted: MFSW buttons, RCD510, Boot pop, Black Monza II, Xenons, Audi jacking points, open fog light grills.

Offline alexperkins

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 7
  • -Receive: 99
  • Posts: 2122
Re: Fitting Cat Back Milltek - Advice
« Reply #4 on: March 09, 2011, 10:41:27 pm »
ooo shiny. Tempts me to get one  :signLOL:
Logged


VCDS Scanning/Coding, RNS and MDI retrofits, and specialist mechanics services with VAGtek available - Just PM me for details.

Offline the bruce

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 322
  • -Receive: 100
  • Posts: 1591
    • my GTI
Re: Fitting Cat Back Milltek - Advice
« Reply #5 on: March 09, 2011, 11:32:07 pm »
I'd order some high quality clamps like this:  :happy2:

http://www.ezt-autoteile.de/Auspuffanlagen/Schalldaempfer-Construct/Edelstahl-Spezial-Bandschelle/Powersprint-Construct-Edelstahl-Spezial-Bandschelle-%D8-68-mm-73-mm::32725.html

Maybe you need a reducer to fit the stock downpipe.
The Milltek catback will be the diameter of the Milltek downpipe.

http://www.ezt-autoteile.de/Auspuffanlagen/Schalldaempfer-Construct/Reduzierrohr:::11533_13301_13325.html

Just examples. Check the sizes by your self !!
Logged
"You get what you pay for."

Offline Gene Hunt

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 59
  • -Receive: 61
  • Posts: 2478
    • Email
Re: Fitting Cat Back Milltek - Advice
« Reply #6 on: March 10, 2011, 10:04:19 am »
Quote from: the bruce on March 09, 2011, 11:32:07 pm
I'd order some high quality clamps like this:  :happy2:

http://www.ezt-autoteile.de/Auspuffanlagen/Schalldaempfer-Construct/Edelstahl-Spezial-Bandschelle/Powersprint-Construct-Edelstahl-Spezial-Bandschelle-%D8-68-mm-73-mm::32725.html

Maybe you need a reducer to fit the stock downpipe.
The Milltek catback will be the diameter of the Milltek downpipe.

http://www.ezt-autoteile.de/Auspuffanlagen/Schalldaempfer-Construct/Reduzierrohr:::11533_13301_13325.html

Just examples. Check the sizes by your self !!
.............as above,looks to me like the reducer clamp is missing(bit needed to fit milltek to the standard cat piece. Contact milltek & they will sell you one,not expensive. :wink:
Logged
ED35. Standard factory condition.

Offline the bruce

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 322
  • -Receive: 100
  • Posts: 1591
    • my GTI
Re: Fitting Cat Back Milltek - Advice
« Reply #7 on: March 10, 2011, 01:38:15 pm »
The outer diameter at the end of the sock downpipe/cat is 60 mm.
Just check the inner diameter of the Milltek. If there's tube insert
with 60.5 - 61 mm everything is fine and you just need a some
exhaust mounting paste (eg Holts).
Logged
"You get what you pay for."

Offline PDT

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 3
  • -Receive: 142
  • Posts: 2010
    • Email
Re: Fitting Cat Back Milltek - Advice
« Reply #8 on: March 10, 2011, 02:33:59 pm »
I have a load of spare milltek reducers for the nk5 here, can have one for the cost of postage :)
Logged

Offline the bruce

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 322
  • -Receive: 100
  • Posts: 1591
    • my GTI
Re: Fitting Cat Back Milltek - Advice
« Reply #9 on: March 10, 2011, 03:10:58 pm »
Very friendly offer !!

 :happy2:
Logged
"You get what you pay for."

Offline bodger00

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 23
  • -Receive: 20
  • Posts: 521
  • A wish called Zonda
Re: Fitting Cat Back Milltek - Advice
« Reply #10 on: March 10, 2011, 08:10:11 pm »
Thanks all for the replies! :notworthy:

There was some daylight left when I got home today so jacked up the car, put it on axle stands and had a look. After measuring the internal diameter of the miltek approx 69mm I definatley need 1 clip and 1 reducer of some sort. I am not sure of the dimensions but I guess they are standard. If I can't use the original clip then I guess I will need two clips and a reducer :rolleye:

@PDT I have sent you a PM :happy2:
Logged
Pages: [1]   Go Up
« previous next »