Make a donation

Author Topic: Upgrading Bushes.....  (Read 3194 times)

Offline apples12

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 6
  • -Receive: 34
  • Posts: 563
Upgrading Bushes.....
« on: March 13, 2012, 04:00:55 pm »
Hi...

I'm looking to change some of the bushes on my Mk5 namely the Front and rear anti roll bar bushes to start with and I was wondering if this was something that could easily be done at home on the driveway? and better still if anyone had any links to any good DIY's?

I was thinking of putting powerflex  ARB bushes in (the current ones are still the original ones fitted 154,800 miles ago!)

thanks
MK6 GT TDI  - CW - LUX pack
GONE
MkV Golf 1.9TDI Sport in DBP, 160,000 miles and climbing!

Retrofits by me:GT front end,OEM bixenons with auto-levelling/washers, Valeo LED Rears, MFSW + Highline SWCM, Cruise Control, 30byte Highline CECM, Highline clocks, Rain/Light Sensor, Auto-dimming Rear view Mirror, RNS-510 LED (Ver H; SW: 4020), Fiscon Basic Bluetooth, MDI + Aux, Armrest, Reverse Camera LOW, TPMS..what next...

Offline RedRobin

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 380
  • -Receive: 442
  • Posts: 16627
  • BIALI Motorsport's Chief Horn Blower
Re: Upgrading Bushes.....
« Reply #1 on: March 13, 2012, 04:08:13 pm »
.
A very stable jack? Take the wheels off and disassemble the suspension. Plus lots of strong elbow grease.

As far as I know for a full set of bushes throughout the Mk5 it's quite a labour intensive job, takes time, and is best done in a workshop with either a pit or a lift thingy.


On facebook: https://www.facebook.com/robin.procter.50

Throbbin' Red Mk5 GTI DSG with too many mods to list - Have Fun but Safe Journeys!

Offline vRS Carl

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 282
  • -Receive: 240
  • Posts: 3088
  • I'm the F.A.G (Forum Apple Guru)
Re: Upgrading Bushes.....
« Reply #2 on: March 13, 2012, 04:23:30 pm »
Rear ones would be easy in the ARB and you could do it at home.

The front involves removing the whole subframe, removing the ARB, cutting the bushing mount, taking the old mount out, putting new one in and then welding it back together and reassembly. You would struggle to do this on the drive unless you had some very tall Axle Stands. Which i think would be dangerous.

I'm not aware (but i haven't looked) of anyone just selling the bracket for the bushing on it's own.
« Last Edit: March 13, 2012, 04:29:06 pm by vRS Carl »

Offline apples12

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 6
  • -Receive: 34
  • Posts: 563
Re: Upgrading Bushes.....
« Reply #3 on: March 13, 2012, 04:31:46 pm »
Hi guys, just got off the phone to VW...

the Rear ARB clamps - 5.99 incl vat, rear bolts 70p incl vat

front ARB - they dont sell the clamps seperate, comes as a complete 'kit'... same story on etka, only listed as a complete 'kit'

so say i would be able to get it into a pit, i'm assuming i'd have to cut out the old bushes and not the clamps as i cant replace those? then the new bush goes in, clamp over the top and bolt in?

no way am i gna replace the entire ARB!
MK6 GT TDI  - CW - LUX pack
GONE
MkV Golf 1.9TDI Sport in DBP, 160,000 miles and climbing!

Retrofits by me:GT front end,OEM bixenons with auto-levelling/washers, Valeo LED Rears, MFSW + Highline SWCM, Cruise Control, 30byte Highline CECM, Highline clocks, Rain/Light Sensor, Auto-dimming Rear view Mirror, RNS-510 LED (Ver H; SW: 4020), Fiscon Basic Bluetooth, MDI + Aux, Armrest, Reverse Camera LOW, TPMS..what next...

Offline vRS Carl

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 282
  • -Receive: 240
  • Posts: 3088
  • I'm the F.A.G (Forum Apple Guru)
Re: Upgrading Bushes.....
« Reply #4 on: March 13, 2012, 04:32:33 pm »
Read my post above yours  :happy2:

Offline apples12

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 6
  • -Receive: 34
  • Posts: 563
Re: Upgrading Bushes.....
« Reply #5 on: March 13, 2012, 04:37:34 pm »
welding?!!  :scared:

is that how VW would do it if they had to replace an anti roll bar bushing?! looks like i may be leaving the front alone....lol
MK6 GT TDI  - CW - LUX pack
GONE
MkV Golf 1.9TDI Sport in DBP, 160,000 miles and climbing!

Retrofits by me:GT front end,OEM bixenons with auto-levelling/washers, Valeo LED Rears, MFSW + Highline SWCM, Cruise Control, 30byte Highline CECM, Highline clocks, Rain/Light Sensor, Auto-dimming Rear view Mirror, RNS-510 LED (Ver H; SW: 4020), Fiscon Basic Bluetooth, MDI + Aux, Armrest, Reverse Camera LOW, TPMS..what next...

Offline vRS Carl

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 282
  • -Receive: 240
  • Posts: 3088
  • I'm the F.A.G (Forum Apple Guru)
Re: Upgrading Bushes.....
« Reply #6 on: March 13, 2012, 04:45:54 pm »
welding?!!  :scared:

is that how VW would do it if they had to replace an anti roll bar bushing?! looks like i may be leaving the front alone....lol

No they would just replace the bar.

Offline rich83

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 165
  • -Receive: 802
  • Posts: 13444
    • MK5 Golf GTI
  • My Ride: https://www.mk5golfgti.co.uk/forum/index.php?PHPSESSID=ad5uig6vlaep9dupvmtqcdjtcm&/topic,19740.0.html
Re: Upgrading Bushes.....
« Reply #7 on: March 14, 2012, 01:57:47 am »
Rear is a doddle.. you don't even need to remove the wheels  :happy2: