Make a donation
« previous next »
Pages: [1]   Go Down

Author Topic: Changing cam follower  (Read 2313 times)

Offline 55golf

  • Always Involved
  • ****
  • Thank You
  • -Given: 1
  • -Receive: 2
  • Posts: 131
    • Email
Changing cam follower
« on: January 06, 2013, 09:52:57 pm »
I am looking at changing this myself on my dsg ed30. Do you need to get the engine TDC before I take the pump out, also is it a case of just taking old one out and dropping new cam follower in
Logged

Offline fab5freddy

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 238
  • -Receive: 239
  • Posts: 2033
Re: Changing cam follower
« Reply #1 on: January 06, 2013, 09:56:48 pm »
Logged

Offline Tortaruga

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 36
  • -Receive: 105
  • Posts: 1527
Re: Changing cam follower
« Reply #2 on: January 06, 2013, 10:03:31 pm »
AFAIK you don't need to set TDC. Setting TDC ensures there will be no pressure exerted on the fuel pump's spring by the inlet camshaft lobe.

If the lobe was at it's highest point the spring would exert some pressure and could possibly strip threads if you were stupid in your manner of removing the hpfp fixing bolts.

Take old one out and drop in new one. Put oil on it first.

Logged
'07 Red manual

Offline 55golf

  • Always Involved
  • ****
  • Thank You
  • -Given: 1
  • -Receive: 2
  • Posts: 131
    • Email
Re: Changing cam follower
« Reply #3 on: January 06, 2013, 10:30:14 pm »
Anyone in the Cheshire area willing to help me :smiley:
Logged

Offline gazbutS3

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 52
  • -Receive: 55
  • Posts: 3213
    • Email
Re: Changing cam follower
« Reply #4 on: January 06, 2013, 10:33:41 pm »
Quote from: 55golf on January 06, 2013, 10:30:14 pm
Anyone in the Cheshire area willing to help me :smiley:

I'm not that far away, in Bolton, if you fancy a drive out I'll do it/show you, I change mine every 10k as part of the service
Logged

Offline ianv5

  • Always Involved
  • ****
  • Thank You
  • -Given: 3
  • -Receive: 12
  • Posts: 437
Re: Changing cam follower
« Reply #5 on: January 07, 2013, 05:46:55 am »
Logged

Offline ROH ECHT

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 113
  • -Receive: 149
  • Posts: 2116
  • K04 PLAY....ZOOM DIS!
Re: Changing cam follower
« Reply #6 on: January 07, 2013, 06:13:00 am »
TDC? No. Just be sure to loosen a bit on each of the three #30 torx head bolts as there is some spring tension on the hpfp. I never have had to turn mine a bit to return the hpfp to the head. I just add some of my body pressure to the hpfp and tighten in the same manner...a bit on each bolt to carefully compress the spring inside. Check out my vid above and you will likely be able to knock it out yourself, yes?
Logged
K04 PLAY...K04 turbo/S3 INJ. & FMIC/FORGE FMTC, TB hose, & WG actuator/GIAC's H.O. K04 & DSG TUNES/AWE DV/NEUSPEED P-FLO,TURBO OUTLET & TB pipe/AUTOTECH hpfp/BSH Eng.&Trans Mounts/H&R ARB's/Whiteline Performance springs & W.A.L.K./ECS stage-3 BBK/BILSTEIN B8's...ZOOM'DIS...GIAC K04 tune-2007 Volkswagen GTI: 12.823 @ 112.050 MPH__Voting for my Dragtimes link: http://www.dragtimes.com/Volkswagen-GTI-Timeslip-25700.html?r=1

Offline RobboGTI

  • Always Involved
  • ****
  • Thank You
  • -Given: 0
  • -Receive: 7
  • Posts: 338
Re: Changing cam follower
« Reply #7 on: January 07, 2013, 06:27:59 am »
Good video. Looks a very straightforward job!
Logged

Offline ianv5

  • Always Involved
  • ****
  • Thank You
  • -Given: 3
  • -Receive: 12
  • Posts: 437
Re: Changing cam follower
« Reply #8 on: January 07, 2013, 06:28:29 am »
Quote from: ROH ECHT on January 07, 2013, 06:13:00 am
TDC? No. Just be sure to loosen a bit on each of the three #30 torx head bolts as there is some spring tension on the hpfp. I never have had to turn mine a bit to return the hpfp to the head. I just add some of my body pressure to the hpfp and tighten in the same manner...a bit on each bolt to carefully compress the spring inside. Check out my vid above and you will likely be able to knock it out yourself, yes?

Do you need to keep the doors shut? I read somewhere that leaving the drivers door open kept the fuel pump primed and fuel would keep flowing?

On a different point how did you do the holes in your fog lamp grills?

Thanks

Ian
Logged

Offline ROH ECHT

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 113
  • -Receive: 149
  • Posts: 2116
  • K04 PLAY....ZOOM DIS!
Re: Changing cam follower
« Reply #9 on: January 07, 2013, 06:56:35 am »
Mine doesn't mind the doors being open, I suppose, as the fuel does not do that.
Logged
K04 PLAY...K04 turbo/S3 INJ. & FMIC/FORGE FMTC, TB hose, & WG actuator/GIAC's H.O. K04 & DSG TUNES/AWE DV/NEUSPEED P-FLO,TURBO OUTLET & TB pipe/AUTOTECH hpfp/BSH Eng.&Trans Mounts/H&R ARB's/Whiteline Performance springs & W.A.L.K./ECS stage-3 BBK/BILSTEIN B8's...ZOOM'DIS...GIAC K04 tune-2007 Volkswagen GTI: 12.823 @ 112.050 MPH__Voting for my Dragtimes link: http://www.dragtimes.com/Volkswagen-GTI-Timeslip-25700.html?r=1

Offline Betty02

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 10
  • -Receive: 11
  • Posts: 685
    • iBett
Re: Changing cam follower
« Reply #10 on: January 07, 2013, 09:42:04 am »
Quote from: gazbutS3 on January 06, 2013, 10:33:41 pm
Quote from: 55golf on January 06, 2013, 10:30:14 pm
Anyone in the Cheshire area willing to help me :smiley:

I'm not that far away, in Bolton, if you fancy a drive out I'll do it/show you, I change mine every 10k as part of the service

I might take you up on this offer too? Does look "easy enough" just scared of breaking something! only from Blackpool!

Thanks
Logged
ADMIN NOTICE: Please do not use the site for advertising!
Pages: [1]   Go Up
« previous next »