All Things Mk5 > How to Guides / Troubleshooting
How To: Mk5 Heated Seats Retrofit
doylebros:
Have you read this guide
http://www.mk5golfgti.co.uk/forum/index.php/topic,62645.0.html
Gmac:
--- Quote from: RetroRaz on October 16, 2017, 10:27:05 am ---The wire that has 2 going into it isn't for cecm.
As far as i remember on the 2007+ loom it's:
2 for ground
3 for the heater panel
2 for fuse box (1 ignition 1 live) there's an additional wire to fuse box if your seat has lumbar support)
1 for cecm
When i fitted a up to 2006 loom there was an additional wire to the above and i couldn't figure out where it goes. Wiring it to an ignition cleared the fault code but the seats still didn't heat up.
Sent from my SM-G955F using Tapatalk
--- End quote ---
Cheers Raz.
My loom has more wires than you are suggesting above. I've got a total of 13 wires i think.
2 for ground
3 for heater panel
4 thick wires - fuse panel? I have lumbar support
2 into 1 - ? thought that was cecm?
2 more wires - shorter and thin?
1 longer wire - long enough to get to control panel
Going to have to take a picture when i get a chance. I've buried it under the trim near the bonnet release handle for the moment. :happy2:
Gmac:
--- Quote from: doylebros on October 16, 2017, 05:53:51 pm ---Have you read this guide
http://www.mk5golfgti.co.uk/forum/index.php/topic,62645.0.html
--- End quote ---
Haha, clearly!!! As you have replied within this post :happy2:
RetroRaz:
Which loom did you buy? If you bought the 2007+ loom then it could be its for a lhd and you will have to swap the looms that are under the seats to convert them back to rhd.
Sounds like the loom you got might also be for the memory seats.
Sent from my SM-G955F using Tapatalk
Gmac:
--- Quote from: RetroRaz on October 17, 2017, 12:37:26 pm ---Which loom did you buy? If you bought the 2007+ loom then it could be its for a lhd and you will have to swap the looms that are under the seats to convert them back to rhd.
Sounds like the loom you got might also be for the memory seats.
Sent from my SM-G955F using Tapatalk
--- End quote ---
Got hold of the instructions from kufatec ......
I've ordered the 'until 2006' as the seats were from a golf from this era...
Pic....
FFS!!!!! Why is everything so hard... Copy and paste from a pdf has screwed up the text... Can't seem to upload the image either....arrrrrgggggghhhhh
Manual wiring heated seats Golf V until October 2006
Wire configuration with gray wirings: 2x Permanent positive (Imprint Dauerplus Kl.30)
2x Permanent positive (Imprint Sitzverstell. Kl.30)
3x Ignition positive (Imprint Zündung Kl.15) 1x Double crimp (Imprint C – PIN 1)
Connection Climate control unit 20-pole connector: 1x Grey wire (0.352) (Imprint Blau/Gelb)
1x Grey wire (0.352) (Imprint Blau/Rot)
1x Grey wire (0.352) (Imprint ZP Klima) -
2x Cable lug (Imprint Masse)
Connection with free fuse at the fuse box (20 ampere each)
Connection with free fuse at the fuse box (30 ampere each)
Only at item 34048-2 & 34048-4
Connection with free fuse at the fuse box (15 ampere each)
Control unit central electric Connector C – PIN 1
PIN 10 (Climatronic) – PIN 13 for Climatic PIN 11 (Climatronic) – PIN 12 for Climatic PIN 12 (Climatronic) – PIN 15 for Climatic
Ground A-Column, driver site
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version