Make a donation
« previous next »
Pages: [1]   Go Down

Author Topic: ITG help!!!!  (Read 1580 times)

Offline 18Edition30

  • Always Involved
  • ****
  • Thank You
  • -Given: 7
  • -Receive: 8
  • Posts: 329
ITG help!!!!
« on: May 24, 2013, 06:32:26 pm »
Guys and girls

Fitted my ITG open induction kit a few nights back and getting on ok with it, not sure if I can live with darth vadar all the time though!

Anyway when stationary and I blip the throttle upto around 5k to show some people the noise it makes, when the revs drop back down to normal they go right down to 500rpm and engine nearly stalls then quickly jump back up to around 900rpm normal tickover, it never used to do this and I'm wondering what is happening? Obviously something to do with the kit.

Any ideas?

Will
Logged

Offline Jabarton99

  • Always Involved
  • ****
  • Thank You
  • -Given: 7
  • -Receive: 3
  • Posts: 79
Re: ITG help!!!!
« Reply #1 on: May 24, 2013, 07:18:09 pm »
When I got my ITG fitted it Iid the same. Took to the garge and it was my maf sensor due to increased air flow. So replaced it and all has Ben fine for 12months + now.
Logged
R32 Recaro bucket seats (individual colour), Golf R MFSW with cream stitching, Cream stitched gear gaitor to match, RNS510, highline cluster, Ko4 turbo, Forge twintercooler, Forge oil catch can & washer bottle, Autotech fuel pump, Neuspeed power pully, S3 injectors, ITG maxogen intake, Red top coil packs, Milltek Full 3" exhaust straight through. AP Coilovers, H & R Anti roll bars, Tarox 10pot calipers front & S3 rear calipers rear.

Offline 18Edition30

  • Always Involved
  • ****
  • Thank You
  • -Given: 7
  • -Receive: 8
  • Posts: 329
Re: ITG help!!!!
« Reply #2 on: May 24, 2013, 07:23:43 pm »
Quote from: Jabarton99 on May 24, 2013, 07:18:09 pm
When I got my ITG fitted it Iid the same. Took to the garge and it was my maf sensor due to increased air flow. So replaced it and all has Ben fine for 12months + now.

So could need new MAF sensor? How much are these?

What's the reason?

Will
Logged

Offline Jabarton99

  • Always Involved
  • ****
  • Thank You
  • -Given: 7
  • -Receive: 3
  • Posts: 79
Re: ITG help!!!!
« Reply #3 on: May 24, 2013, 07:44:44 pm »
Apparently they get dirty and when they have been on the car a while and you increase air flow they don't like it. It's not 100 % that but I bet you that's where a garage would start. There about £80 I think but it's been a while since mine was done. You can clean them but I beleive it's very tricky and doesn't always work.
Logged
R32 Recaro bucket seats (individual colour), Golf R MFSW with cream stitching, Cream stitched gear gaitor to match, RNS510, highline cluster, Ko4 turbo, Forge twintercooler, Forge oil catch can & washer bottle, Autotech fuel pump, Neuspeed power pully, S3 injectors, ITG maxogen intake, Red top coil packs, Milltek Full 3" exhaust straight through. AP Coilovers, H & R Anti roll bars, Tarox 10pot calipers front & S3 rear calipers rear.

Offline bacillus

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 4
  • -Receive: 451
  • Posts: 6327
Re: ITG help!!!!
« Reply #4 on: May 24, 2013, 07:46:18 pm »
Quote from: 18Edition30 on May 24, 2013, 07:23:43 pm
So could need new MAF sensor? How much are these?

Usually around £120-130...  :scared:
Logged
Without traction power is nothing!

Offline 56OctyVRS

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 39
  • -Receive: 72
  • Posts: 1003
Re: ITG help!!!!
« Reply #5 on: May 25, 2013, 02:04:35 pm »
Try some electrical contact cleaner on the maf first.
Logged
Frozen White Ford Focus 1.6 Ecoboost Titanium.
Mods so far - Superchips Bluefin, High Flow Air Box

Offline GrayMK5GTI

  • Global Moderator
  • Just look at my post count
  • *
  • Thank You
  • -Given: 125
  • -Receive: 247
  • Posts: 4165
Re: ITG help!!!!
« Reply #6 on: May 25, 2013, 05:59:06 pm »
Quote from: 56OctyVRS on May 25, 2013, 02:04:35 pm
Try some electrical contact cleaner on the maf first.

X2 sound advice

It's about £5 from Maplins or Halfords. Remove the sensor from the housing, cover it in cleaner, leave it a short while to dry then try again. A lot cheaper than a new MAF.

Made my car a lot smoother after cleaning the MAF  :happy2:
Logged
NOW: 2015 Golf R DSG 5 Door, Lapiz Blue, 19s, Discover Nav, Reversing Camera
GONE:2007 Black GTI Edition 30 3dr

Offline 18Edition30

  • Always Involved
  • ****
  • Thank You
  • -Given: 7
  • -Receive: 8
  • Posts: 329
Re: ITG help!!!!
« Reply #7 on: May 25, 2013, 08:54:03 pm »
So is this most probably the problem then?

Will try tomorrow.

Cheers
Logged

Offline edd666999

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 24
  • -Receive: 89
  • Posts: 2730
    • Email
Re: ITG help!!!!
« Reply #8 on: May 26, 2013, 02:45:42 pm »
Cleaned mine with the halfords stuff £3.99. Didn't however fix my issue lol.
Logged

Offline Marshall

  • Always Involved
  • ****
  • Thank You
  • -Given: 14
  • -Receive: 17
  • Posts: 348
Re: ITG help!!!!
« Reply #9 on: May 26, 2013, 03:00:50 pm »
If the car was ok beforehand I think I'd be checking the pipe on to the turbo to make sure its seated properly.
This sounds more like unmetered air getting in through a leak after the maf.
I'd check that when the clip has been tightened on to the turbo it hasn't ridden up on one side.
Also check maf is securely fitted, I'm pretty sure they only fit one way.
Logged
MISANO RED RS3

Offline RedED30

  • Always Involved
  • ****
  • Thank You
  • -Given: 19
  • -Receive: 3
  • Posts: 176
Re: ITG help!!!!
« Reply #10 on: May 26, 2013, 04:20:22 pm »
Quote from: Marshall on May 26, 2013, 03:00:50 pm
If the car was ok beforehand I think I'd be checking the pipe on to the turbo to make sure its seated properly.
This sounds more like unmetered air getting in through a leak after the maf.
I'd check that when the clip has been tightened on to the turbo it hasn't ridden up on one side.
Also check maf is securely fitted, I'm pretty sure they only fit one way.

Agree with all of this. i'd be checking everything is seated 100% and cleaning the maf before shelling out for new one.
Logged
Revo Stage2 - With Linear Throttle
Revo DSG
BCS Turboback Powervalve - This is a must.
ITG Closed Intake.. wooosh

Here to enjoy and help, with a hint of sarcasm, please do not be offended

Offline 56OctyVRS

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 39
  • -Receive: 72
  • Posts: 1003
Re: ITG help!!!!
« Reply #11 on: May 26, 2013, 10:25:13 pm »
Also make sure the seal that fits between the maf and intake is fitted also.
Logged
Frozen White Ford Focus 1.6 Ecoboost Titanium.
Mods so far - Superchips Bluefin, High Flow Air Box

Offline 18Edition30

  • Always Involved
  • ****
  • Thank You
  • -Given: 7
  • -Receive: 8
  • Posts: 329
Re: ITG help!!!!
« Reply #12 on: May 27, 2013, 05:28:46 pm »
Quote from: GrayMK5GTI on May 25, 2013, 05:59:06 pm
Quote from: 56OctyVRS on May 25, 2013, 02:04:35 pm
Try some electrical contact cleaner on the maf first.

X2 sound advice

It's about £5 from Maplins or Halfords. Remove the sensor from the housing, cover it in cleaner, leave it a short while to dry then try again. A lot cheaper than a new MAF.

Made my car a lot smoother after cleaning the MAF  :happy2:

Just spray on and leave to dry?

Don't wipe with cloth or anything no?

And you mean on the actual MAF itself don't you?,, not the electrical points lol.

Sorry for the silly questions.

Cheers again
Logged

Offline edd666999

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 24
  • -Receive: 89
  • Posts: 2730
    • Email
Re: ITG help!!!!
« Reply #13 on: May 27, 2013, 05:36:11 pm »
Quote from: 18Edition30 on May 27, 2013, 05:28:46 pm
Quote from: GrayMK5GTI on May 25, 2013, 05:59:06 pm
Quote from: 56OctyVRS on May 25, 2013, 02:04:35 pm
Try some electrical contact cleaner on the maf first.

X2 sound advice

It's about £5 from Maplins or Halfords. Remove the sensor from the housing, cover it in cleaner, leave it a short while to dry then try again. A lot cheaper than a new MAF.

Made my car a lot smoother after cleaning the MAF  :happy2:

Just spray on and leave to dry?

Don't wipe with cloth or anything no?

And you mean on the actual MAF itself don't you?,, not the electrical points lol.

Sorry for the silly questions.

Cheers again

you can spray it on both providing its electrical contact cleaner
Logged
Pages: [1]   Go Up
« previous next »