yellow cupra k1, polish testing

[cuprajake]

Nope ;) I used the old gulf bulb holders in line.  So I'll still get bulb light of one goes out ;)

[Tfsi_Mike]

Might get in touch next spring when I get round to doing it 

[cuprajake]

done as much as i can now, stuck due to christmas post, pressure switch hasnt come so i cant bench test till after the new yr :(

but ive done the bulk

here it is


IMAG0905 by cuprajake1, on Flickr


IMAG0911 by cuprajake1, on Flickr


IMAG0909 by cuprajake1, on Flickr

all mounted, may still rotate the tank more depending on the size of the tank, once ive pressure tested i can then hare wire it in place,

these are the wireless senders for the pressure gauge up front, there attached to schreder valves so should i have an issuse i can still air each corner induvidually


IMAG0908 by cuprajake1, on Flickr

jake

[chrisr763]

Very nice! Smart looking setup and for a very reasonable price. Have you done this before? 

[cuprajake]

IMAG0918 by cuprajake1, on Flickr


IMAG0919 by cuprajake1, on Flickr


IMAG0920 by cuprajake1, on Flickr

jake

[cuprajake]

electrics sorted


IMAG0933 by cuprajake1, on Flickr


IMAG0936 by cuprajake1, on Flickr

jake

[TommyR]

Looking forward to see the finished product!

[cuprajake]

Just a small update. I've still not got the pressure switch so I'm stuck.

Today I quickly fit the blanks to the tank asw ell as the outlet and as a make shift fit a gauge on there where the switch goes.

I wanted to leak test the tank. So far so good. Pressure has held at 100psi for the last three hours. I'll see what it's like in the morning.

I've also Ordered an accuair speed switch as a controller instead of the switch box I made. Purely as I had birthday and Christmas money haha.


http://bagriders.com/modlab/products/SWITCHSPEED-CONTROLLER.html

[xjay1337]

Nice one Jake :) looking forward to when it's all working.

[cuprajake]

Me too. Christmas wasted loads of time lol

Where do you have your remote.

[cuprajake]

controller turned up, along with the rebuild kit and the pressure switch

so finished the panel


IMAG1059 by cuprajake1, on Flickr


accuair manifold will be here tomoz,

jake

[xjay1337]

Looks really good jake impressed.
Gonna get tyres of my wheels asap and get them split down for you ;)

[cuprajake]

cheers, let me know when your ready to send

also built the struts up

took the old bits off, then cleaned and greased the parts as they went back on


IMAG1062 by cuprajake1, on Flickr


IMAG1064 by cuprajake1, on Flickr

pic of the strut built up dint come out, crappy phone.

then a nice tnt driver brought me this


IMAG1067 by cuprajake1, on Flickr

tripple r composites splitter


the manifold is due tomorrow, then all i need is air line and i have pretty much everything i need to start installing it,

in the next week or so ill finish off my boot mount, and get the wire through to the door for the controller with a view to fitting it next weekend


jake

[cuprajake]

had a change of heart with the controller, main reason being the wire has to go through the door but the leon uses the full lock block, no where for the wire to go

it would mean taking the door off, drilling a hole for the cable etc so i decided on a new location


IMAG1070 by cuprajake1, on Flickr

its the cup holder section under the mdf2

so i made a bracket, primed and painted


IMAG1068 by cuprajake1, on Flickr

this is the bracket in situe, i used foam tape under the bracket then bolted down, this wat we get no vibration. the steel is about 5mm thick lol


IMAG1085 by cuprajake1, on Flickr

and finally in its home..


IMAG1092 by cuprajake1, on Flickr

jake

[cuprajake]

well propper pissed off right now,

today is the first chance i have been able to test the front struts after fitting the rebuild kit....guess what one leaks real bad, sold by an ed38 member whos also in the trade to me as working, it needs a new bag which is over £100

cant trust nobody!!!!!!