Make a donation
« previous next »
Pages: 1 [2]   Go Down

Author Topic: Faults found help  (Read 3723 times)

Offline doylebros

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 44
  • -Receive: 309
  • Posts: 2775
Re: Faults found help
« Reply #15 on: February 24, 2014, 05:17:48 pm »
Clear the DTCS. For that module then redo the measuring block testes then an output test and see if the faults still there.
Logged

Offline reaper7881

  • Always Involved
  • ****
  • Thank You
  • -Given: 3
  • -Receive: 4
  • Posts: 210
  • My Ride: http://www.mk5golfgti.co.uk/forum/index.php/topic,68492
Re: Faults found help
« Reply #16 on: February 24, 2014, 06:20:28 pm »
Does your car have a rain light sensor
Logged
54 MK5 Golf 1.9tdi 3dr SMD Full Interior and Speedo Conversion, GTi Highline , Flat Bottom Wheel, ED30 Rear lights

Offline jakex181

  • Always Involved
  • ****
  • Thank You
  • -Given: 4
  • -Receive: 2
  • Posts: 202
Re: Faults found help
« Reply #17 on: February 24, 2014, 06:26:15 pm »
yeah the car has a rain light sensor as it has auto wipers and headlights
Logged

Offline jakex181

  • Always Involved
  • ****
  • Thank You
  • -Given: 4
  • -Receive: 2
  • Posts: 202
Re: Faults found help
« Reply #18 on: February 25, 2014, 01:06:44 pm »
I have noticed that sometimes ill put the auto wipers on and they will be going crazy even with the smalled bit of rain and I adjusting the sensitivity does nothing, does this prove its the switch?
Logged

Offline doylebros

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 44
  • -Receive: 309
  • Posts: 2775
Re: Faults found help
« Reply #19 on: February 25, 2014, 03:30:15 pm »
My thought would still be with the switch - dealer says they sells more switches than rain sensors!
Logged

Offline jakex181

  • Always Involved
  • ****
  • Thank You
  • -Given: 4
  • -Receive: 2
  • Posts: 202
Re: Faults found help
« Reply #20 on: February 25, 2014, 05:56:35 pm »
Ive got a new switch on the way, do i have to remove the steering wheel to replace it? i hope not! :/
Logged

Offline jakex181

  • Always Involved
  • ****
  • Thank You
  • -Given: 4
  • -Receive: 2
  • Posts: 202
Re: Faults found help
« Reply #21 on: February 26, 2014, 12:02:31 pm »
Is there a way to actually test the intake runner control using vagcom?
Logged

Offline doylebros

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 44
  • -Receive: 309
  • Posts: 2775
Re: Faults found help
« Reply #22 on: February 26, 2014, 03:44:27 pm »
Logged

Offline bacillus

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 4
  • -Receive: 451
  • Posts: 6332
Re: Faults found help
« Reply #23 on: February 26, 2014, 04:30:07 pm »
Quote from: jakex181 on February 26, 2014, 12:02:31 pm
Is there a way to actually test the intake runner control using vagcom?


Yes, you can do the output test.

open vcds>engine>output test 03



then select Intake manifold flap from the drop down list



While the test is running the actuator arm should move to fully open and close the flaps
Logged
Without traction power is nothing!
Pages: 1 [2]   Go Up
« previous next »