Make a donation
« previous next »
Pages: [1]   Go Down

Author Topic: Help with xenon shutter wire?  (Read 1488 times)

Offline STV4R

  • Always Involved
  • ****
  • Thank You
  • -Given: 0
  • -Receive: 2
  • Posts: 107
Help with xenon shutter wire?
« on: March 05, 2014, 11:04:50 am »
This weekend when i get my car back I'm going to be fitting my xenon headlights, but i have no idea where to run the wire for the shutters.
So if someone could be kind enough and take a few photos of where they run their wires in the engine bay it would be much appreciated.
Thanks
Steve
Logged

Offline marko

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 16
  • -Receive: 33
  • Posts: 903
    • Email
Re: Help with xenon shutter wire?
« Reply #1 on: March 05, 2014, 11:20:12 am »
Just google fitting xenons on mk5 golf..lots of write ups on there
The wires basically run from the 12 pin harness at the lamp to the cecm in under the steering wheel..
Is your car a highline option??
Logged
2007 TR gt170...heated leather,underseat drawers,auto-levelling bi-xenons,puddle leds,chrome switches,footwell lights f+r,cruise control and ed30 rear lamps,LED interior....carbon highline clocks,ed30 front spoiler,RNS 510 P+MDI,mk6 gti gearknob,TPMS done,complete r32 trim kit+ MFSW,r32 f+r brakes,RLS fitted.headlamp washers,folding mirrors and boot pop,mk6 RVC,19"Helios,AP coilies,valeo LEDs  ...dpf delete and remap to finish off

Offline STV4R

  • Always Involved
  • ****
  • Thank You
  • -Given: 0
  • -Receive: 2
  • Posts: 107
Re: Help with xenon shutter wire?
« Reply #2 on: March 05, 2014, 11:38:20 am »
I know the shutter wires have to run to the CECM. What i want to know is where do you run the wires around the engine bay? so it looks nice and tidy and what should i wrap the wire up with?
All the guides i find dont really show where to run the wires. They just show they need to connect to pin D/6 and A/5 in the CECM and yes i have highline
thanks
Logged

Offline Luka

  • Always Involved
  • ****
  • Thank You
  • -Given: 6
  • -Receive: 32
  • Posts: 388
Re: Help with xenon shutter wire?
« Reply #3 on: March 05, 2014, 12:22:39 pm »
I ran them parallel to the bonnet pull cable, if you wrap it in harness tape first it looks tidy; just enough room to tuck it under the trim that holds the cable. Then just go through the bulkhead and into the drivers footwell.
Logged
Sold - 2006 Tornado Red GTI 3dr

Offline STV4R

  • Always Involved
  • ****
  • Thank You
  • -Given: 0
  • -Receive: 2
  • Posts: 107
Re: Help with xenon shutter wire?
« Reply #4 on: March 05, 2014, 10:40:07 pm »
Quote from: Luka on March 05, 2014, 12:22:39 pm
I ran them parallel to the bonnet pull cable, if you wrap it in harness tape first it looks tidy; just enough room to tuck it under the trim that holds the cable. Then just go through the bulkhead and into the drivers footwell.

Sounds good
cheers
Logged
Pages: [1]   Go Up
« previous next »