So Jay’s detailing guide is what you need to read on this subject but here’s my brief guide on what work I have done on my car that’s achievable without going into depth. A weekend mechanics guide if you will. Here is the link to Jay’s thorough guide
http://www.mk5golfgti.co.uk/forum/index.php/topic,74892.0.htmlI’ll list the products as I go and the steps throughout. I’ll do exterior first followed by interior. I’m writing down here what works for me from a tried and tested routine. Some people prefer to apply certain products before others etc. so just do what suits you. 1 missed step won’t ruin a car!
ExteriorStep 1: Rinse
Pressure washer everything, not too close and not too high a pressure for fear of damaging car. Don’t forget wheel arches and brake calipers.
Step 2: Snowfoam 1
I use CNP demon foam and a homemade lance adapted for my pressure washer. Just spray it on and leave to remove the more stubborn dirt then rinse off after 5 or 10mins.
Step 3: Pre Clean
I use orchard citrus pre clean diluted down to how about my car is. This removes all traces of old waxes and sealants for a fresh base.
Step 4: Snowfoam 2
Apply some more snow because you’re guaranteed to have missed something and rinse.
Step 5: Two Bucket Method
I use a microfiber wash mitt with my two buckets. Start from the roof down and wash in straight lines. Dip and agitate mitt on grit guard after every stroke in rinse bucket. Work from the top down. Don’t go near the back bumper, skirts, underbelly, wheels, arches etc. with the same wash mitt as these areas will be filthy and contain traces of old chemicals.
When you’re all done, change water if needed in buckets and change to a coarser wash mitt. Now tackle the areas excluded above before a final rinse.
Step 6: Iron X
Get it all over the car, wheels would be the main culprit. Don’t do it in direct sunlight and leave for no longer than 5 mins or it WILL stain and rinse again.
Step 7: Clay
Start claying the car, I make the clay lube from a mix of autoglym shampoo and water. Follow your clay guide but basically it’s straight lines, medium pressure. Don’t forget the wheels and a final rinse all over.
Step 8: Dry 1
I have a chemical guys wooly mammoth microfiber drying towel. Dry in straight lines with towel folded into quarters. As each corner becomes saturated, flip over. I only dry here now as I don’t see the point in drying before applying Iron X and clay and rinsing again just to dry a second time.
Step 9: Polish
Refer to a more in depth guide here but basically I have a DAS6 pro polisher, chemical guys V34, V36 and V38 polishes which range from heavy to light and a range of chemical guys microfiber foam and microfiber pads.
Start with heavy cutting pad and V34 compound polish working up to medium polishing pad and V36 cutting polish and finishing with finishing microfiber pad and V38 final polish.
It’s not rocket science. Use good lighting to see how you’re doing and ask a friend to see if “you missed a spot”. You can also benefit from a paint thickness gauge if you want to splash out!
NOTE: Mask off all of the rubber seals and any areas that are of a dissimilar material. The polisher generates huge amounts of heat through friction and if placed on certain areas such as rubber sills it can actually cause severe damage.
Also as pointed out by Jay, your back bumper and certain trims will be made of plastic coated in paint in comparison to your metal panels coated in paint. Different pressures will be required when working on different materials so start off light!
Now this is where I go off the beaten track. I also polish my lights, the black gloss pillars and the glass. Use some common sense here with polishes and start at the lightest working your way to heavier cut as required.
The reason I polished the glass is for application of G1 later on. I use specific glass polish here.
Step 10: Snowfoam 3
Get to snowfoaming again to remove all the polish residue and any bits you may have missed and then a good rinse.
Step 11: Dry 2
Same as above.
Step 12: Glaze
I applied 3 coats now of chemical guys glossworks glaze. It’s tough on the arms but follow the label and you’re fine. Remember that the less you put on the easier it will be to buff off later. Buff off residue after it has time to stick. Apply all your coats and then get ready to seal. The glaze fills the tiny swirls and chips that you missed in polishing.
Just some of the items I used below
Step 13: Sealant
I applied 3 coats of jetseal 109. Wait 20 mins after each application before applying the next. Don’t forget to do your wheels too but I wouldn’t bother with the plastic trims.
Step 14: Wax
I applied 3 coats of autoglym super HD wax. Don’t let it sit for too long or it’s tough to buff off. Again out of direct sunlight.
Step 15: Windscreen Protection
Now that it’s polished from earlier on I applied some G1. It’s a hydrophobic coating that you paint on and it’s amazing!! Just dab it on with the cotton pads provided. Wait a while and apply 2 more coats to the front. Remove residue with the residue remover supplied. Buff the hell out of it with a microfiber cloth after. It may seem like you’re removing the coating but you’re not. This stuff seems to get into the glass on a microscopic level. With the left over amount in the bottle give all other windows a single coat as they don’t need the full 3.
Step 16: Polish Exhausts
Refer to my build thread for a full breakdown of this.
Step 18: Apply Trim Coating
Apply your black trim coating to rear bumper, front splitter and side skirts.
Step 19: Tyre Gel
Apply tyre gel but keep it far from the newly cleaned alloys.
InteriorStep 1: Petrol Cap
Open your petrol cap and clean out all the grit inside. Unblock the small valve on the bottom of the sump to allow future water to drain and snowfoam it all if need be. Don’t forget a quick bit of grease on the hinge too!
Step 2: Door Trims
This is a good 2 hour job. I use chemical guys all purpose cleaner diluted down 10:1 with water and spray it on. Remove all of the old grease and gunk and seal it up with jetseal 109 and or wax. Don’t forget to regrease the doors.
Step 3: Drainage Channels
These are the channels that take the rain water build up from the windscreen and drop it to the ground. They get stuffed full of leaves so remove the 2 wipers and the plastic trim. Gather all you can by hand and power hose the rest. If you feel up to it then you can remove the plastic wheel arch protection. The channel drains down just behind here so sand and grit build up at the bottom of the arch. I scooped a pint glass full out last time.
Step 4: Engine Bay
Again chemical guys all purpose diluted 10:1. If you’re feeling brave you can tape off electrical parts and power hose the bay also.
Step 5: Hoover & Canned Air
Before hovering, sweep down all the crap from high level working your war down. I use a Hurricane O2 canless air system which blasts air at 220mph. The vents in particular annoy me so a blast with this and the dust that kicks out is unbelievable. Also handy for the crevices around the window and fuel switches.
Hoover everything. Take the seats out and get down the sides. I guarantee you even find money. They’re held in place with 4 spline bolts. See build thread if you need.
Step 6: Pre Clean
Dilute chemical guys APC to 20:1 for interior use and get spraying. Wipe up with microfiber cloth.
Step 7: Leather Clean & Condition
After a quick warm water clean off the seats I applied some leather conditioner. The conditioner gets sucked up by the leather depending on the condition so do a few coats with special attention to bolster and seatbelt area.
Step 8: Steering Wheel, Gear Stick & Handbrake
There’s a few how to’s on this already. A hot moist towel stuck on the area for a while opens the pores on the leather. The brush and agitate with warm soapy water. Apply leather conditioner and dry.
Step 9: Polish
Use displex polish to clean scratches on radio screen and clocks.
Step 10: Internal Glass
Clean the internal glass as normal. Apply a small amount of fairy liquid to a dry micribfibre cloth and apply to window. Make sure it’s all dry or you’ll have a soapy mess. Leave for a while and buff off. This will leave a hydrophobic coating on the window and condensation will not build up at all. Usually I apply a new coat every 3 months but it’s amazing!
Step 11: Last Few Bits
I clean down the plastic trims and foot pedals with APC. Don’t use anything slippy!
A very weak dilution of APC will remove your girlfriends make up stains all over the passenger visor.
Remove your spare wheel and hoover all around. Check the pressure of it while you’re there!
If you’re using chemical guys liquid spray air freshener don’t apply it to cloth as it leaves a sticky residue. I sometimes remove the carpets and spray the floor before putting carpet back on top.
