rear camber adjustment

[jimmy-s3]

Can anyone give me an idiot proof guide to adjusting the rear camber on my car please. Ive just fitted a set of new wheels and the nsr is rubbing. Looking at the car from the back, the osr wheel has more angle on it then the other side.

[jonnyc]

Can anyone give me an idiot proof guide to adjusting the rear camber on my car please. Ive just fitted a set of new wheels and the nsr is rubbing. Looking at the car from the back, the osr wheel has more angle on it then the other side.

Don't have a guide, but I would say that adjusting camber, or any geometry settings, is not an eye it up type of job.. You need to have it set up and measured to be sure you don't turn your car into an oversteery mess..

The adjustment on the rear camber comes from the cam bolt on the inner side of the rear bottom arms, rotate them and it will move the bottom arm, in or out from the centre line of the car adding or taking away camber..

[Gene Hunt]

Can anyone give me an idiot proof guide to adjusting the rear camber on my car please. Ive just fitted a set of new wheels and the nsr is rubbing. Looking at the car from the back, the osr wheel has more angle on it then the other side.

.........it's recomended after any wheel/suspension change to have a full tracking check done.Get down to you'r local tyre place.    .

[jimmy-s3]

Think i'll take it to where i had my bmw done. They charged £30 for it. Do you think they will set the camber up to factory set up or will they do it to how i want it??

[jonnyc]

Think i'll take it to where i had my bmw done. They charged £30 for it. Do you think they will set the camber up to factory set up or will they do it to how i want it??

Dont think it makes any difference to them does it? Just request a setting if you know what you want 

[pazz]

Think i'll take it to where i had my bmw done. They charged £30 for it. Do you think they will set the camber up to factory set up or will they do it to how i want it??

Whats the rim width and offset on the new wheels? Is the car lowered?

There is nothing wrong with the factory setup. Dont forget that when you lower a car you change the whole geometry of the car suspension.

If you've just fitted bad wheels then camber may solve the rubbing problem but will not help cornering.

[jimmy-s3]

The rim size on the new wheels is 8 or 8.5 im not too sure and the offset i think is 40. (BBS CH reps). Just looking at the car from the rear you can tell the camber is not matching up on both sides. I want it set up to factory really but i think they will rub like mad !

[pazz]

Is the car lowered? If so springs or coilovers?

A bit unusual for the camber to just be out on one side if you've not lowered it.

[jimmy-s3]

Yeah its on coilovers!

[Top Cat]

This is going to sound mad but i think the drivers side rear set up sticks out about 2 mil further. 
When i was setting mine up, or rather VWR were, i kept getting rubbing on the drivers side only. Even when they measured both sides and matched the coils accordingly.

Also if you have got 8.5j wheels with 40 offset then you will get rubbing on severe compression no matter what you do unless you add lots of camber. 

[pazz]

I wrote a lengthy post, but it timed me out! Fkin awesome forum!

Cutting the story short, I'd take it along to a wheel alignment specialist and get them to inspect. Did you fit the coilovers yourself?

[Top Cat]

I wrote a lengthy post, but it timed me out! Fkin awesome forum!

    all you have to do is press post again, and this solves the time out. 

[pazz]

I wrote a lengthy post, but it timed me out! Fkin awesome forum!

    all you have to do is press post again, and this solves the time out. 

It asked me to log back in, so I did. And then it just displayed a blank reply box stating that I'd left it blank???

[Top Cat]

I wrote a lengthy post, but it timed me out! Fkin awesome forum!

    all you have to do is press post again, and this solves the time out. 

It asked me to log back in, so I did. And then it just displayed a blank reply box stating that I'd left it blank???

Ah i see, i thought you meant the post timed out. Being timed out on the forum is a strange one, it happens to a few people even when you select stay logged in always. 

[pazz]

I wrote a lengthy post, but it timed me out! Fkin awesome forum!

    all you have to do is press post again, and this solves the time out.  

It asked me to log back in, so I did. And then it just displayed a blank reply box stating that I'd left it blank???

Ah i see, i thought you meant the post timed out. Being timed out on the forum is a strange one, it happens to a few people even when you select stay logged in always.  

Mine was set to 240 minutes, but it sure as hell didnt take 4 hours to write! I've ticked the box for "always keep me logged in". Thanks the help TC. Apologies for off-topic Jimmy-S3